3W UV LED灯 60度石英玻璃透镜 45度玻璃透镜 365nm

详细信息

联系方式

3W 365nm 375nm 385nm 395nm 405nm 410nm 415nm 420nm 大功率紫外线UVLED ，45度和60度石英玻璃透镜 3535尺寸 

 

Features  特点
● CMH real inorganic package 纯石英玻璃封装   
● Dimension尺寸 3.70mm×3.70mm×2.67mm  
● Long operating life 超长工作寿命
● High reliability 高质量高稳定性
● Superior ESD protection防静电保护
● RoHS compliant

Applications 应用领域
● Fluorescent spectroscopy  荧光检测  荧光激发
● Sensors and monitors  传感器 感应探头
● Bio-analysis/detection 生物聚合
● Phototherapy 光疗 
● UV curing  固化
● Printing  喷涂印刷
● Coating 涂覆

 

参数

Peak Wavelength 波长：360-420nm  可选

Radiant Flux  光功率：1355-1641mW/cm2

Forward Voltage 电压：3.4-4.2V

Forward Current 电流：1200mA  

View Angle 出光角度：45°   60°

 

 

Notes:
*This LED is designed to be reflow soldered on to a PCB. If dip soldered or hand soldered,
We cannot guarantee its reliability.
*Reflow soldering must not be performed more than twice.
*Avoid rapid cooling. Ramp down the temperature gradually from the peak temperature.
*Nitrogen reflow soldering is recommended. Air flow soldering conditions can cause optical degradation,
caused by heat and/or atmosphere.
*Since the glass used in the encapsulating glass is fragile, do not press on the hermetic glass.
pressure can cause nicks, chip-outs, Sealant layer and deformation, and wire breaks, decreasing reliability
*Repairing should not be done after the LEDs have been soldered.
It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
*The Die Heat Sink should be soldered to customer PCB. If it is difficult or impossible, use high heat-dissipating adhesive.
*When soldering, do not apply stress to the LED while the LED is hot.
*When using a pick and place machine, choose an appropriate nozzle for this product.
*When flux is used, it should be a halogen free flux. Ensure that the manufacturing process is not designed in a manner
Where the flux will come in contact with the LEDs.
*Make sure that there are no issues with the type and amount of solder that is being used.

*此LED设计为回流焊接到印刷电路板上。如果是浸焊或手工焊，我们无法保证其可靠性。
*回流焊接不得超过两次。
*避免快速冷却。从最高温度逐渐降低温度。
*建议采用氮气回流焊接。气流焊接条件会导致光学性能下降，由热和/或大气引起。
*由于封装玻璃中使用的玻璃易碎，请勿按压密封玻璃。压力会导致缺口、切屑、密封剂层和变形，以及断丝，降低可靠性。
*在焊接LED后，不应进行维修。应事先确认修理是否会损坏LED的特性。
*模具散热器应焊接到客户印刷电路板上。如果困难或不可能，使用高散热粘合剂。
*焊接时，不要在LED发热时对其施加应力。
*当使用拣配工具时，请为本产品选择合适的夹具。
*使用助焊剂时，应为无卤助焊剂。确保制造工艺的设计不符合要求。磁通量将与发光二极管接触的地方。
*确保使用的焊料类型和数量没有问题。

 

CAUTIONS
1. Handling Precautions
● Do not handle the LEDs with bare hands as it will contaminate the LEDs surface and may
affect the optical characteristics.
● When handling the product with tweezers, be careful not to apply excessive force to the
glass. Otherwise, the glass can be cut, chipped, delaminate or deformed, causing wire-bond
breaks and catastrophic failures.
■  Dropping the product may cause damage.
2. Electrostatic Discharge (ESD)
● The product are sensitive to static electricity or surge voltage. ESD can damage a die and
its reliability. When handling the products, the following measure against electrostatic dis-
charge are strongly recommended:
Eliminating wrist strap, ESD footwear, clothes, and floors
Grounded workstation equipment and tools
ESD table/shelf mat made of conductive materials
● Ensure that tools, jigs and machines that are being used are properly grounded and that
proper grounding techniques are used in work areas. For devices/equipment that mount the
LEDs, protection against surge voltages should also be used.
● The customer is advised to check if the LEDs are damage by ESD
When performing the characteristics inspection of the LEDs in the application.
Damage can be detected with a forward voltage measurement at low current(≤1mA).
3. Eye Safety
● Please proceed with caution when handling any UVLEDs driven at low or high current.
Since UV light can be harmful to eyes, do Not look directly into the UV light, even through an
optical instrument.
●  UV protective glasses are required to use in order to avoid damage by UV light in case of
viewing UV light directly.

 

注意事项
1. 处理措施
●不要徒手操作LED灯,因为它将发光二极管表面污染和可能影响光学特性。
●用镊子夹LED灯时,注意不要过度使用暴力夹住玻璃。否则，玻璃可能会被切割、破碎、分层或变形，导致金属丝粘结断裂和灾难性故障。
■产品掉落可能造成损害。
2. 静电放电(ESD)
●产品对静电或电压冲击敏感。静电可以损坏模具和它的可靠性。处理产品时，应采取以下防静电措施
强烈建议:
消除腕带，静电鞋，衣服和地板上面的静电
做好接地防静电
由导电材料制成的静电桌子/搁板垫子
●确保工具、夹具和机械使用正确接地
确保正在使用的工具、夹具和机器正确接地，并在工作区域使用正确的接地技术。对于安装led的设备，也应该使用防止浪涌电压的保护。
●建议客户检查LED 灯是否被ESD损坏
在应用程序中对led进行特性检查时。
检测伤害要在低电流正向电压测量(≤1 ma)。
3.眼睛安全
●请谨慎处理任何UVLEDs驱动的低或高电流。
因为紫外线对眼睛有害，所以不要直视紫外线，即使是通过光学仪器。
●在直接观看紫外线的情况下， 为了避免紫外线的伤害，需要使用防紫外线眼镜

免责声明：以上信息由会员自行提供，内容的真实性、准确性和合法性由发布会员负责。集萃丝印特印网对此不承担任何责任。

联系我的时候！请说明在集萃丝印特印网上看到的，我好做备案！